SUMMERS OPTICAL CAT#: 12800
SUMMERS PRODUCT: Milbond Type I
Part A
DATE 06/12/2005

MATERIAL SAFETY DATA SHEET
CATALYST FOR LENS BOND
The information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy of this data or the results to be obtained from the use thereof. Summers Optical assumes no responsibility for personal injury or property damage to vendees, users or third parties caused by the material. Such vendees or users assume all risks associated with the use of the material.

Summers Optical, A Division of EMS Acquisition
1560 Industry Road - P O Box 380 - Hatfield, PA 19440
TEL: (215) 412-8380 - FAX: (215) 412-8450

24 Hour Emergency Phone # Chemtrec: 800/424-9300

FOR PRODUCT AND SALES INFORMATION
CONTACT SUMMERS OPTICALS OFFICE ABOVE

PRODUCT IDENTIFICATION

PRODUCT NAME:

  Lens Bond Optical Cement Type
Milbond Type I Part A

HAZARDOUS INGREDIENTS
 

OSHA PEL

AGGIH TLV

OTHER EXP LIMITS

%OPT

CAS#
Fumed Silica:

20mppcf

5mg/m3

N/A

1

7631-86-9
Bisphenol
A/Epichlorhydrin Resin:

N/E

 N/E N/A

52.5

25068-38-6
Red Iron Oxide:

N/A

 N/A   46.5  1309-37-1 
   N/A = Not Applicable N/E = Not Established      

PHYSICAL AND CHEMICAL CHARACTERISTICS

BOILING POINT:

 >500°F/260°C

MELTING POINT:

 N/A

SPECIFIC GRAVITY (H2O=1):

 1.769

VAPOR PRESSURE (mm Hg):

 .03 @ 77°C

VAPOR DENSITY (Air=1) :

 N/AP

APPEARANCE/ODOR:

 Rust Brown thick paste.

SOLUBILITY IN WATER:

 Insoluble

REACTIVITY IN WATER:

 Non reactive

FIRE AND EXPLOSION HAZARD DATA

FLASH POINT:

 480°F/250°C

METHOD USED:

 PMCC

EXPLOSION LEVEL-LOWER (LEL):
-UPPER (UEL):

 N/A
N/A

AUTO-IGNITION TEMPERATURE:

 250°C SADT*

EXTINGUISHER MEDIA:

 This material will not readily support combustion.

FIRE FIGHTING PROCEDURES:

 Use foam, dry chemical or CO2. Fire-fighters should protect eyes and use self contained breathing apparatus.

UNUSUAL FIRE AND EXPLOSION HAZARDS:

 At temperatures above 500°F, Aldehydes, acids and other organic substances may be formed. Vapors may be toxic.
* SELF ACCELERATING DECOMPOSITION TEMPERATURE  

REACTIVITY DATA

STABILITY:

 Stable

CONDITIONS TO AVOID:

 None

MATERIALS TO AVOID:

 Strong oxidizing agents. Mineral acids

HAZARDOUS DECOMPOSITION PRODUCTS:

 Carbon Monoxide, Aldehydes, and acids during combustion.

HAZARDOUS POLYMERIZATION:

 Will not occur

CONDITIONS TO AVOID:

 Strong oxidizing agents. Lewis or mineral acids, mineral or organic bases especially Aliphatic Amines.

HEALTH HAZARDS

ACUTE:

 None (See Chronic)

CHRONIC:

 Some eye or skin sensitization

SIGNS AND SYMPTOMS OF EXPOSURE:

 Very low reactivity, some reddening of eyes or skin rash (Hives).

MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:

 Any existing skin or eye disorders.

CHEMICAL LISTED AS A CARCINOGEN
OR POTENTIAL CARCINOGEN:

 NTP: No
IARC: No
OSHA: No

EMERGENCY AND FIRST
AID PROCEDURES:

 Flush eyes for 15 minutes with water. Remove soiled clothing and wash skin with soap and water.

 

ROUTES OF ENTRY:

INHALATION:

 Very Unlikely: resin has very low volatility.

EYES:

 Unlikely: Flush with plenty of water, get medical attention.

SKIN:

 Likely: wash thoroughly with soap and water.

INGESTION:

 Least likely: Do not induce vomiting. LD/50 11.4gm/kg (rat).

PRECAUTION FOR SAFE HANDLING AND USE

SPILLS OR LEAKS:

 Absorb with clay or sand and dispose in accordance with local regulations.

WASTE DISPOSAL:

 Best method is to catalyze and dispose of cured material.

STORAGE AND HANDLING:

 Store in cool, dry location with adequate ventilation.

OTHER PRECAUTIONS:

 Keep away from open flame or very hot environment, avoid contact with strong acids and bases.

CONTROL MEASURES

RESPIRATORY PROTECTION:

 Normally not required except during combustion of product.

VENTILATION:

 Local Exhaust: Yes
Mechanical (General) Yes
Special: None
Other: None

PROTECTIVE GEAR:

 Finger cots or impervious gloves. Safety glasses or face shield. Always use Niosh approved equipment.

WORK/HYGIENIC PRACTICES:

 Always wash skin thoroughly with soap and water before eating or smoking.

ECOLOGICAL INFORMATION:

ECOTOXICOLOGICAL INFORMATION:

 N/A

CHEMICAL FATE:

 N/A

TRANSPORT INFORMATION

DOT SHIPPING NAME:

 Paint

HAZARD CLASS:

 3

PACKING GROUP:

 II

UN/NA NO:

 1263

DOT LABELS:

 Flammable Liquid

SUBSIDIARY LABELS:

 None

DOT PLACARDS:

 3, Flammable Liquid

 IATA SHIPPING NAME:

 Paint

 HAZARD CLASS:

 3

 PACKING GROUP:

 II

 UN NO:

 1260

 IATA LABELS:

 Flammable Liquid

 SUBSIDIARY LABEL:

 None

IMO SHIPPING NAME:

 Paint

HAZARD CLASS:

 3

PACKING GROUP:

 II

UN/NA NO:

 1263

 SUBSIDIARY LABELS:

 None

REGULATORY INFORMATION

NOT APPLICABLE

Back to MSDS Menu | Back to Main Menu

 

 

SUMMERS OPTICAL CAT#: 12800
SUMMERS PRODUCT: Milbond Type I
Part B
DATE 05/05/2002

MATERIAL SAFETY DATA SHEET
CATALYST FOR LENS BOND
The information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy of this data or the results to be obtained from the use thereof. Summers Optical assumes no responsibility for personal injury or property damage to vendees, users or third parties caused by the material. Such vendees or users assume all risks associated with the use of the material.

Summers Optical, A Division of EMS Acquisition
1560 Industry Road - P O Box 380 - Hatfield, PA 19440
TEL: (215) 412-8380 - FAX: (215) 412-8450

24 Hour Emergency Phone # Chemtrec: 800/424-9300

FOR PRODUCT AND SALES INFORMATION
CONTACT SUMMERS OPTICALS OFFICE ABOVE

PRODUCT IDENTIFICATION
PRODUCT NAME: Lens Bond Optical Cement Type
Milbond Type I Part B

HAZARD IDENTIFICATION
OSHA PEL AGGIH TLV OTHER EXP LIMITS %OPT CAS#
Butadiene/Acrylonitrile Co-Polymer: 69.5 68683-29-4
Contains:          
Acrylonitrile: 2ppm 2ppm
(skin)		 N/A <1ppm in product
Butadiene: 1000ppm 10ppm N/A <7ppm in product
Hydrogen Cyanide:

10ppm
(skin)

 10ppm
(skin)

N/A

<5ppm in product

  
N-Aminoethyl Piperazine:

N/E

N/E

N/A

<5% in product

  
Versamid 140:

N/E

N/E

N/A

28.25

68410-23
DMP-30:

5ppm
(skin)

5ppm
(skin)

N/A

2.25

90-72-2
   N/A = Not Applicable
N/E = Not Established		      

PHYSICAL AND CHEMICAL CHARACTERISTICS
BOILING POINT: 130°F/160°C
MELTING POINT: N/E
SPECIFIC GRAVITY (H2O=1): .944
VAPOR PRESSURE (mm Hg): .01 @ 21°C
VAPOR DENSITY (Air=1) : N/E
APPEARANCE/ODOR: Thick bluish-green/Amine odor
SOLUBILITY IN WATER: Insoluble
REACTIVITY IN WATER: Non reactive

FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: 240°F/115°C
METHOD USED: 5CC
EXPLOSION LEVEL-LOWER (LEL):
-UPPER (UEL):		 N/E
N/E
AUTO-IGNITION TEMPERATURE: N/E
EXTINGUISHER MEDIA: ABC Dry chemical foam
FIRE FIGHTING PROCEDURES: Firefighters should wear full protective clothing including self contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Although this product does not easily support combustion, high temperatures can cause the emission of oxides of Nitrogen.

REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: High Temperatures >200°F
INCOMPATABILITY
(MATERIALS TO AVOID):		 Strong oxidizers, i.e. Hydrogen Peroxide Permanganates and Perchlorate.
HAZARDOUS DECOMPOSITION PRODUCTS: CO, CO2, Oxides of Nitrogen and Ammonia
HAZARDOUS POLYMERIZATION: Will not occur
CONDITIONS TO AVOID: See above information

HEALTH HAZARDS
ACUTE: Eye and Skin Irritation
CHRONIC: Skin rashes and upper respiratory irritation.
SIGNS AND SYMPTOMS OF EXPOSURE: Reddening of skin or eyes.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Pre-existing respiratory, skin or eye disorders may be aggravated.
CHEMICAL LISTED AS A CARCINOGEN
OR POTENTIAL CARCINOGEN:		 NTP: No
IARC: No
OSHA: No
EMERGENCY AND FIRST
AID PROCEDURES:		 Flush eyes with water for 10 minutes. Remove soiled clothing and wash. Wash skin thoroughly with soap and water. Induce vomiting and remove to fresh air.

 

ROUTES OF ENTRY:

INHALATION:

 Very Likely: remove to fresh air, assist breathing if necessary.

EYES:

 Not Likely: If proper eye protection is worn.

SKIN:

 Most Likely: Wash thoroughly with soap and water.

INGESTION:

 Least Likely: Induce vomiting. LD/50=10.3gm/kg (Rat).

PRECAUTION FOR SAFE HANDLING AND USE
SPILLS OR LEAKS: Absorb with suitable absorbant (sand) and dispose of properly. Milbond is not considered a hazardous waste.
WASTE DISPOSAL: Best method is to catalyze and dispose of solid material.
STORAGE AND HANDLING: Store in a well ventilated area and do not process or mix without proper ventilation.
OTHER PRECAUTIONS: Keep away from heat and strong oxidizers

CONTROL MEASURES
RESPIRATORY PROTECTION: Niosh approved respirator if necessary
VENTILATION: Local Exhaust: Yes
Mechanical (General) Yes
Special: None
Other: None
PROTECTIVE GEAR: Rubber or plastic gloves. Safety glasses or face shield. Eye wash station. Plastic or rubber apron.
WORK/HYGIENIC PRACTICES: Always wash thoroughly with soap and water before eating or smoking.

ECOLOGICAL INFORMATION:
ECOTOXICOLOGICAL INFORMATION: N/A
CHEMICAL FATE: N/A

TRANSPORT INFORMATION
DOT SHIPPING NAME: Paint
HAZARD CLASS: 3
PACKING GROUP: II
UN: 1263
DOT LABELS: Flammable Liquid
SUBSIDIARY LABELS: None
DOT PLACARDS: 3, Flammable Liquid
   
IMO SHIPPING NAME: Paint
HAZARD CLASS: 3
PACKING GROUP: II
UN: 1263

 SUBSIDIARY LABEL:

 None

 IATA SHIPPING NAME:

  Paint

HAZARD CLASS:

  3

PACKING GROUP:

  II

UN NO:

  1263

IATA LABELS:

  Flammable Liquid

SUBSIDIARY LABEL:

  None

REGULATORY INFORMATION

NOT APPLICABLE

Back to MSDS Menu | Back to Main Menu