SUMMERS OPTICAL CAT#: 12801
SUMMERS PRODUCT: Milbond Type II (Part A)
DATE 06/12/2006

MATERIAL SAFETY DATA SHEET
CATALYST FOR LENS BOND
The information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy of this data or the results to be obtained from the use thereof. Summers Optical assumes no responsibility for personal injury or property damage to vendees, users or third parties caused by the material. Such vendees or users assume all risks associated with the use of the material.

Summers Optical, A Division of EMS Acquisition
1560 Industry Road - P O Box 380 - Hatfield, PA 19440
TEL: (215) 412-8380 - FAX: (215) 412-8450

24 Hour Emergency Phone # Chemtrec: 800/424-9300

FOR PRODUCT AND SALES INFORMATION
CONTACT SUMMERS OPTICALS OFFICE ABOVE

PRODUCT IDENTIFICATION

PRODUCT NAME:

  Lens Bond Optical Cement Type - Milbond Type II (Part A)

HAZARDOUS INGREDIENTS
 

OSHA PEL

AGGIH TLV

OTHER EXP LIMITS

% OPT

CAS#
Fumed Silica:

20mppcf

5mg/m3

N/A

1

7631-86-9
Bisphenol A/Epichlorhydrin Resin:

N/E

N/E

N/A

52.5

 25068-38-6
Red Iron Oxide:

N/A

N/A

46.5

 1309-37-1
N/E = NOT ESTABLISHED
N/A = NOT APPLICABLE		          

PHYSICAL AND CHEMICAL CHARACTERISTICS

BOILING POINT:

 >500°F/260°C

MELTING POINT:

 N/A

SPECIFIC GRAVITY [H2O=1] :

 1.769

VAPOR PRESSURE [mm Hg] :

 .03 @ 77°C

VAPOR DESENSITY [Air=1]:

 N/AP

APPEARANCE/ODOR:

 Rust Brown thick paste.

SOLUBILITY IN WATER:

 Insoluble

REACTIVITY IN WATER:

 Non Reactive

FIRE AND EXPLOSION HAZARD DATA

FLASH POINT:

 480°F/250°C

METHOD USED:

 PMCC

EXPLOSION LEVEL-LOWER (LEL):
-UPPER (UEL):

 N/A
N/A

AUTO-IGNITION TEMPERATURE:

 250°C SADT*

EXTINGUISHER MEDIA:

 This material will not readily support combustion.

FIRE FIGHTING PROCEDURES:

 Use foam, dry chemical or CO2. Firefighters should protect eyes and use self contained breathing apparatus.

UNUSUAL FIRE AND EXPLOSION HAZARDS:

 At temperatures above 500°F, Aldehydes, acids and other organic substances may be formed. Vapors may be toxic.
* SELF ACCERATING DECOMPOSITION TEMPERATURE. 

REACTIVITY DATA

STABILITY:

 Stable

CONDITIONS TO AVOID:

 None

INCOMPATIBILITY MATERIALS TO AVOID:

 Strong oxidizing agents. Mineral acids.

HAZARDOUS DECOMPOSITION PRODUCTS:

 Carbon Monoxide, Aldehydes, and acids during combustion.

HAZARDOUS POLYMERIZATION:

 Will not occur.

CONDITIONS TO AVOID:

 Strong oxidizing agents. Lewis or mineral acids, mineral or organic bases especially Aliphatic Amines.

HEALTH HAZARDS

ACUTE:

 None (See chronic)

CHRONIC:

 Some eye or skin sensitization.

SIGNS AND SYMPTOMS OF EXPOSURE:

 Very low reactivity, some reddening of eyes or skin rash (Hives).

MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:

 Any existing skin or eye disorders.

CHEMICAL LISTED AS A CARCINOGEN
OR POTENTIAL CARCINOGEN:

 NTP: No
IARC: No
OSHA: No

EMERGENCY AND FIRST
AID PROCEDURES:

 Flush eyes 15 minutes with water. Remove soiled clothing and wash skin with soap and water.

 

ROUTES OF ENTRY:

INHALATION:

 Very unlikely: resin has very low volatility.

EYES:

 Unlikely: Flush with plenty of water, get medical attention.

SKIN:

 Likely: wash thoroughly with soap and water.

INGESTION:

 Least likely: Do not induce vomiting. LD/50 11.4gm/kg (rat).

PRECAUTION FOR SAFE HANDLING AND USE

SPILLS OR LEAKS:

 Absorb with clay or sand and dispose in accordance with local regulations.

WASTE DISPOSAL:

 Best method is to catalyze and dispose of cured material.

STORAGE AND HANDLING:

 Store in a cool, dry lacation with adequate ventilation.

OTHER PRECAUTIONS:

 Keep away from open flame or very hot environment, avoid contact with strong acids and bases.

CONTROL MEASURES

RESPIRATORY PROTECTION:

 Normally not required except during combustion of product.

VENTILATION:

 Local Exhaust: Yes
Mechanical (General) Yes
Special: None
Other: None

PROTECTIVE GEAR:

 Finger cots or impervious gloves. Safety glasses or face shield. Always use Niosh approved equipment.

WORK/HYGIENIC PRACTICES:

 Always wash skin thoroughly with soap and water before eating or smoking.

ECOLOGICAL INFORMATION:

ECOTOXICOLOGICAL INFORMATION:

 N/A

CHEMICAL FATE:

 N/A

TRANSPORT INFORMATION

NON-RESTRICTIVE

REGULATORY INFORMATION

NOT APPLICABLE

Back to MSDS Menu | Back to Main Menu

 

 

SUMMERS OPTICAL CAT#: 12801
SUMMERS PRODUCT: Milbond Type II (Part B)
DATE 05/05/2002

MATERIAL SAFETY DATA SHEET
CATALYST FOR LENS BOND
The information contained herein is based on data considered accurate. However, no warranty is expressed or implied regarding the accuracy of this data or the results to be obtained from the use thereof. Summers Optical assumes no responsibility for personal injury or property damage to vendees, users or third parties caused by the material. Such vendees or users assume all risks associated with the use of the material.

Summers Optical, A Division of EMS Acquisition
1560 Industry Road - P O Box 380 - Hatfield, PA 19440
TEL: (215) 412-8380 - FAX: (215) 412-8450

24 Hour Emergency Phone # Chemtrec: 800/424-9300

FOR PRODUCT AND SALES INFORMATION
CONTACT SUMMERS OPTICALS OFFICE ABOVE

PRODUCT IDENTIFICATION

PRODUCT NAME:

  Lens Bond Optical Cement Type - Milbond Type II (Part B)

HAZARDOUS INGREDIENTS
  OSHA PEL AGGIH TLV OTHER EXP LIMITS % OPT CAS#
Butadiene/Acrylonitrile Co-Polymer: N/E N/E N/E 69.5 68683-29-4
Acrylonitrile: 2ppm 2ppm
(skin)		 N/A <1ppm in
(product)		  
Butadiene: 1000ppm 10ppm N/A <7ppm in
(product)		  
Hydrogen Cyanide: 10ppm (skin) 10ppm (skin) N/A <5ppm in
(product)		  
N-Aminoethyl Piperazine: N/E N/E N/A <5% in
(product)		  
Versamid 140: N/E N/E N/A 28.25 68410-23
DMP-30: 5ppm (skin) 5ppm (skin) N/A 2.25 90-729-2
N/E = NOT ESTABLISHED
N/A = NOT APPLICABLE		          

PHYSICAL AND CHEMICAL CHARACTERISTICS
BOILING POINT: 130°F/160°C
MELTING POINT: N/E
SPECIFIC GRAVITY: (H2O=1) .944
VAPOR PRESSURE: (mm Hg) .01 @ 21°C
VAPOR DESENSITY: (Air=1): N/E
APPEARANCE/ODOR: Thick bluish-green/Amine odor
SOLUBILITY IN WATER: Insoluble
REACTIVITY IN WATER: Non Reactive

FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: 240°F/115°C
METHOD USED: 5CC
EXPLOSION LEVEL-LOWER (LEL):
-UPPER (UEL):		 N/E
N/E
AUTO-IGNITION TEMPERATURE: N/E
EXTINGUISHER MEDIA: ABC Dry chemical foam
FIRE FIGHTING PROCEDURES: Firefighters should wear full protective clothing including self contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Although this product does not easily support combustion, high temperatures can cause the emission of oxides of Nitrogen.

REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: High temperatures >200°F
MATERIALS TO AVOID: Strong oxidizers, i.e. Hydrogen Peroxide Permanganates and Perchlorate.
HAZARDOUS DECOMPOSITION PRODUCTS: CO, CO2, Oxides of Nitrogen and Ammonia
HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: SEE ABOVE

HEALTH HAZARDS
ACUTE: Eye and shin irritation.
CHRONIC: Skin rashes and upper respiratory irritation.
SIGNS AND SYMPTOMS OF EXPOSURE: Reddening of skin or eyes.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Pre-existing respiratory, skin or eye disorders may be aggravated.
CHEMICAL LISTED AS A CARCINOGEN
OR POTENTIAL CARCINOGEN:		 NTP: No
ARC: No
OSHA: No
EMERGENCY AND FIRST
AID PROCEDURES:		 Flush eyes with water for 10 minutes. Remove soiled clothing and wash. Wash skin thoroughly with soap and water. Induce vomiting and remove to fresh air.

 

ROUTES OF ENTRY:

INHALATION:

 Very likely: remove to fresh air, assit breathing if necessary.

EYES:

 Not likely: If proper eye protection is worn.

SKIN:

 Most Likely: wash thoroughly with soap and water.

INGESTION:

 Least likely: induce vomiting. LD/50=10.3gm/kg (Rat).

PRECAUTION FOR SAFE HANDLING AND USE
SPILLS OR LEAKS: Absorb with suitable absorbant (sand) and dispose of properly. Milbond is not considered a hazardous waste.
WASTE DISPOSAL: Best method is to catalyze and dispose of solid material.
STORAGE AND HANDLING: Store in a well ventilated area and do not process or mix without proper ventilation.
OTHER PRECAUTIONS: Keep away from heat and strong oxidizers.

CONTROL MEASURES
RESPIRATORY PROTECTION: Niosh approved respirator if necessary
VENTILATION: Local Exhaust: Yes
Mechanical (General) Yes
Special: None
Other: None
PROTECTIVE GEAR: Rubber or plastic gloves. Safety glasses or face shield. Eye wash station. Plastic or rubber apron.
WORK/HYGIENIC PRACTICES: Always wash thoroughly with soap and water before eating or smoking.

ECOLOGICAL INFORMATION:
ECOTOXICOLOGICAL INFORMATION: N/A
CHEMICAL FATE: N/A

TRANSPORT INFORMATION

NON RESTRICTIVE

REGULATORY INFORMATION

NOT APPLICABLE

Back to MSDS Menu | Back to Main Menu