Questions? 800-523-5874 | [email protected]
- Prepmaster™ Specimen Preparation Robot
- TEM Grids
- TEM Window Grids
- Omniprobe Nanomanipulation Systems
- K-kit Wet "Liquid" TEM Kit
- Specimen Mounts
- SEM Specimen Holders
- Index and Finder SEM Grids
- SEM for Forensics
- SEM Sample Preparation Station Materials
- Cryogenic Personal Protection Equipment
- Cryo Dewars & Flasks
- Cryogenic Grids & Accessories
- Cryogenic Vials & Racks
- Cooling Chambers & Ice Baths
- Prepmaster™ Specimen Preparation Robot
- Laboratory Microwave Ovens
- LYNX II Automated Tissue Processor
- EMS Poly III
- Microtomes
- Tissue Slicers
- Rapid Immersion Freezer
- Heaters & Chillers
- SEM Cooling Stage
- Glow Discharge Systems
- Sputter Coaters & Carbon Coaters
- Stages
- Freeze Dryers
- Critical Point Dryers
- Cryo-SEM Preparation System
- Specimen Transfer Systems
- Decontaminators
- Desiccators
- Centrifuges
- Dry Baths
- Stirrers, Hot Plates
- Vortexers & Magnetic Mixers
- Rotators & Rockers
- Ovens & Incubators
- Vibration Isolation
- Air Sampling
- Vacuum Pumps
EMS Technical Data Sheets
Tweezers Style 5TTH
EMS Catalog #78320-5TTH
Stainless steel type SA
General notes:
- -Low carbon austenitic steel (Material number 1.4435, DIN X2CrNiMo18-14-3, AISI number 316L)
- - contains from 16.5 to 18.5 wt% chromium and has important quantities of nickel and molybdenum as additional alloying elements
- - non-magnetizable (80%)
- - good corrosion resistance to most chemicals, salts and acids
- - generally used where corrosion resistance and toughness are primary requirements
- - excellent corrosion resistance to most chemicals, salts and acids
- - typical applications include tweezers for the electronic industry, watch-makers, jewelers and laboratory and
medical applications in moderately aggressive chemical environments
Composition
| Component | Wt.% | Component | Wt.% | Component | Wt.% |
| C | ≤ 0.03 | Si | ≤ 1.0 | Mn | ≤ 2.0 |
| P | ≤ 0.045 | S | ≤ 0.03 | Cr | 17.0-19.0 |
| Mo | 2.5-3.0 | Ni | 12.5-15.0 |
Mechanical properties
| State | annealed |
| Density | 8.0 g/cm3 |
| Hardness, Vickers | 230 HV |
| Tensile strength, ultimate | 500-700 MPa |
| Tensile strength, yield | 290 |
| 0.2% Yield stress | ≥ 200 MPa |
| Elongation, break | 40% |
| Modulus of elasticity | 200 GPa |
Thermal properties
| Coef. of lin. therm expansion | 16.0 E-6/°C | 20°C-100°C |
| Coef. of lin. therm expansion | 17.0 E-6/°C | 20°C-300°C |
| Specific heat capacity | 0.50 J/(g .K) |
|
| Thermal conductivity | 15 W/(m.K) | |
| Continuous use temperature | 350°C | |
| Max service temperature, air | 925°C |
Electrical properties
| Resistivity | 0.75 E-4 Ohm.cm |