Questions? 800-523-5874 | [email protected]
- Prepmaster™ Specimen Preparation Robot
- TEM Grids
- TEM Window Grids
- Omniprobe Nanomanipulation Systems
- K-kit Wet "Liquid" TEM Kit
- Specimen Mounts
- SEM Specimen Holders
- Index and Finder SEM Grids
- SEM for Forensics
- SEM Sample Preparation Station Materials
- Cryogenic Personal Protection Equipment
- Cryo Dewars & Flasks
- Cryogenic Grids & Accessories
- Cryogenic Vials & Racks
- Cooling Chambers & Ice Baths
- Prepmaster™ Specimen Preparation Robot
- Laboratory Microwave Ovens
- LYNX II Automated Tissue Processor
- EMS Poly III
- Microtomes
- Tissue Slicers
- Rapid Immersion Freezer
- Heaters & Chillers
- SEM Cooling Stage
- Glow Discharge Systems
- Sputter Coaters & Carbon Coaters
- Stages
- Freeze Dryers
- Critical Point Dryers
- Cryo-SEM Preparation System
- Specimen Transfer Systems
- Decontaminators
- Desiccators
- Centrifuges
- Dry Baths
- Stirrers, Hot Plates
- Vortexers & Magnetic Mixers
- Rotators & Rockers
- Ovens & Incubators
- Vibration Isolation
- Air Sampling
- Vacuum Pumps
EMS Technical Data Sheets
EMS MyFuge™ Mini Centrifuge
EMS Catalog #87041 Series
Introduction
Thank you for purchasing the EMS MyFuge™ Mini Centrifuge! Please be sure to carefully read through this manual prior to operating the instrument. The MyFuge™ Mini Centrifuge is designed for low-speed applications and quick spin downs of microcentrifuge tubes and for eight position PCR strips.
Specifications
| Speed: | 6000rpm/2000xg |
| Capacity: | 8 x 1.5/2.0 ml |
| 32 x 0.2 ml or 4 x PCR strips | |
| Dimensions: | 4.5 (W) x 5.9 (D) x 4.5 (H) in. |
| 11.4 (W) x 15 (D) x 11.4 (H) cm | |
| Electrical: | 120V to 240V, 50-60 Hz |
| Max. Radius: | 3.9 cm |
Installation
Place the MyFuge™ Mini Centrifuge on a flat and level surface nearby an electrical outlet. It should not be near a heat source or in direct sunlight.
Rotor Range
The MyFuge™ Mini Centrifuge includes a second rotor that is designed for holding PCR tubes and PCR strips. The rotor is conveniently stored in a bottom compartment on the bottom of the centrifuge. To access this rotor, turn the machine upside down and remove it from the compartment.
- Removing the rotor from the motor shaft
- The new Clik-n-Lok™ rotor attachment system allows for instant exchange of rotors. To remove a rotor, simply pull it upwards, off the shaft – no tool is required.
- Attaching the rotor to the motor shaft
- Place the rotor on the motor shaft and press down until the rotor comes to a stop. The rotor is now secured – no tool is required.
Operation
- Attach the power cord and place the power switch into the ON position.
- Open the lid and load your samples into the rotor. Always ensure a balanced load.
- Close the lid-the rotor quickly accelerated to the maximum speed of 6200 rpm.
- When the desired run time is completed, push on the lid-the rotor quickly brakes to a stop and the samples until the rotor has come to a complete stop of liquid. See below.
Loading the Rotor
To ensure safe operation and long life of the instrument, samples must always be loaded into the rotor in a balanced fashion. Tubes and strips must always be loaded symmetrically across from one another and contain the same volume of liquid. See diagram at right.
Cleaning and Maintenance
The centrifuge rotors can be removed for cleaning. Once removed, the rotors can be cleaned with isopropyl alcohol or can be sterilized in an autoclave at 121°C for 20 minutes.